Change or rekey · Indian Point
Lock Replacement & Upgrade in Indian Point
The century home's original mortise lock takes a key the size of a spoon, sticks in humid weather and has worn its strike to a groove. You want a lock that works every day without giving up the old door.
Lock Replacement & Upgrade
In plain words
A replacement lock has to fit holes that already exist, and that is where the visit begins. The locksmith measures the backset, the distance from the door edge to the centre of the bore, which on most doors is 60 or 70 millimetres, checks the cross-bore diameter and edge-bore size, notes door thickness and handing, and looks at the strike cut-out. Most residential hardware is made to these standard preparations, so the new lock usually drops into place with no new drilling. Where a mortise lock or a thick door departs from the norm, filler plates, extension kits or a careful new bore bring the door up to standard.
How the visit goesThe brass handleset has gone blotchy and green where the winter salt reaches it, and the coating on the deadbolt is lifting in flakes. It still locks, but it looks tired beside the fresh paint on the door.
Indian Point
How the visit goes
Who is asking for the change
The first check is about the person, not the door. An owner can change any lock on their home. A tenant who wants new hardware on the unit door needs the landlord's agreement, and a landlord who changes a lock while a tenant lives there hands over new keys. The locksmith asks which situation applies and, where paperwork helps, looks at identification, a deed, a lease or a property-management note. It takes a minute and it means the new lock goes on with everyone who has a stake in the door knowing about it, which is exactly how a lock should start its working life.
Setting and reinforcing the strike
The strike side is where a replacement earns most of its value. With the door closed, the bolt is thrown and its mark checked against the pocket so the strike can be positioned to accept the full throw without rubbing. A shallow pocket is deepened until the bolt seats to its stop. Then a reinforced strike or a strike box is fitted using 75 millimetre screws that pass through the jamb and bite into the framing behind it, which is what stops a jamb splitting under a kick. Where an old forced entry has cracked the wood, it is glued and dowelled or a repair plate is fitted first.
Every lock tried the way you will use it
Before the tools go back in the van, each lock is operated from both sides with the door open, then closed, then closed hard against the weatherstrip. The latch should catch on its own when the door swings shut, the deadbolt should throw to its stop with a fingertip on the thumb-turn and no shoulder on the door, and the key should turn without lifting or jiggling. You are invited to try each one yourself and to lock up behind the locksmith. Anything that felt marginal has been adjusted, so the door you close that night behaves the same as the one you tested.
Lock Replacement & Upgrade
In the van
- Boring jig and hole saws
- Knob or lever entry set
- Manufacturer-approved cylinder lubricant
- Handleset with matching deadbolt
- Reinforced strike plate and strike box
What affects the quote
Same fees day, night or weekend
1Finish and style
Standard satin nickel or brass is one line; specialty finishes, matched suites across several doors and designer handlesets are others. The finish you choose for exposure and looks is priced as the maker prices it.
2Keying alike and rekeying
Pinning new cylinders to one key and repinning existing locks to match is work per cylinder, so a whole house on a single key is quoted by the number of locks joining it.
3Condition of the old hardware
Hardware that comes off cleanly is one thing; painted-over trim, seized or stripped screws and a cylinder that has to be drilled out add time before the new lock can go on.
Lock Replacement & Upgrade: questions
Can every door in the house work from one key?
Yes, provided the cylinders share a compatible keyway, which the locksmith checks when choosing hardware. New cylinders are pinned on site to a single new key and any existing locks worth keeping are repinned to match. Front, back, side and garage doors commonly end up on one key, and a shed or gate padlock can join them. You then decide how many copies exist and who holds each.
Can I stop people copying my house key?
A restricted keyway helps with that. The key blanks are controlled by the manufacturer and its authorised locksmiths, so a copy generally requires the card, record or authorisation the program uses, cutting down on copies made at an ordinary kiosk. It suits homes where keys are lent to cleaners, contractors or tenants. The cylinders are fitted in the normal way, and you keep the key card safe because it is what future copies depend on.
Do I have to prove I own the home before you change a lock?
The locksmith will ask, and it is a sign of a careful trade. Photo identification with the address, a deed or property tax notice, or a mortgage or insurance document is plenty for an owner. Tenants show a lease and the landlord's consent; landlords show ownership and confirm the tenant will receive keys. It is a short step that protects everyone with a right to that door.
Change or Rekey Locks
Lock Replacement & Upgrade near you
These are the services we bring to doors across Indian Point. Residential work covers lockouts, rekeying, lock replacement, deadbolts, smart locks and older hardware brought back to life. Commercial work covers storefront doors, exit devices, closers, master keys and safes. Vehicle key cutting rounds out the list when it is needed.